From 33613a85afc4b1481367fbe92a17ee59c240250b Mon Sep 17 00:00:00 2001 From: Sven Eisenhauer Date: Fri, 10 Nov 2023 15:11:48 +0100 Subject: add new repo --- .../en_CCNA4_v30/index/commands/ch1/index.html | 664 +++++++++++++++++++++ 1 file changed, 664 insertions(+) create mode 100644 Bachelor/CCNA4/en_CCNA4_v30/index/commands/ch1/index.html (limited to 'Bachelor/CCNA4/en_CCNA4_v30/index/commands/ch1') diff --git a/Bachelor/CCNA4/en_CCNA4_v30/index/commands/ch1/index.html b/Bachelor/CCNA4/en_CCNA4_v30/index/commands/ch1/index.html new file mode 100644 index 0000000..fac63e0 --- /dev/null +++ b/Bachelor/CCNA4/en_CCNA4_v30/index/commands/ch1/index.html @@ -0,0 +1,664 @@ + + + + + + + + Commands + + + +
+
+ + + + + + + + + + + + + + + + +
+
+ Cisco Systems		 + + + + + +
+ +

+  		 + + + + +
+ +

+ +
+ + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +
+
+ + +
+ + + + + + + + +
Modules:  + + + |  1  |  + 2  |  + 3  |  + 4  |  + 5  |  + 6  |  + CS  |  + All  |
+ + + + + +
+ + + + + +
Module 1: + Scaling IP Addresses
+  + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +
  + Command + Command Description + Command Syntax
+ 1.1.4 + ip route 199.99.9.32 255.255.224.0 + 200.2.2.18 + To establish static routes, use the + + ip route + global configuration + command. To remove static routes, use the + + no + form of this command. + ip route prefix mask {address + | interface-type interface-number [ip-address]} [distance] [tag tag] [permanent]
  + ip nat pool public_access + 199.99.9.40 199.99.9.62 netmask 255.255.255.224 + To define a pool of IP addresses for NAT, use the + + ip nat pool + global configuration command. To remove one + or more addresses from the pool, use the + + no + form of this command. + + ip nat pool name start-ip end-ip + {netmask netmask | prefix-length prefix-length}[type rotary]
  + access-list 1 permit 10.10.10.0 + 0.0.0.255 + To define an access-control list, use the + + + access-list + global + configuration command. To remove a standard access lists, use the + + no + form of this command. + + IP standard access-list: access-list access-list-number + {deny | + permit | remark line} source[source-wildcard] [log]
  + ip nat inside source list 1 pool + public_access + To enable NAT of the inside source + address, use the + ip nat inside source + global configuration command. To + remove the static translation or remove the dynamic association to a + pool, use the + no + form of this command. + ip nat inside source {list + {access-list-number |name} {pool name | interface + dialer-name} + [overload] | static local-ip global-ip}
  + ip nat inside + To designate that traffic originating from or destined for the + interface is subject to NAT, use the + + ip + nat interface + configuration command. To prevent the interface from + being able to translate, use the + + no + form of this command. + + ip nat {inside | outside}
  + ip nat outside + To designate that traffic originating from or destined for the + interface is subject to NAT, use the + + ip + nat interface + configuration command. To prevent the interface from + being able to translate, use the + + no + form of this command. + ip nat {inside | outside}
  + show ip nat translations + To display active NAT translations, use + the + show ip nat + translations EXEC command. + show ip nat translations + [verbose]
  + ip nat inside source list 1 + interface serial 0 overload + To enable NAT of the inside source + address, use the + ip nat inside source + global configuration command. To + remove the static translation or remove the dynamic association to a + pool, use the + no + form of this command. + + ip nat inside source {list {access-list-number |name} {pool + name | + interface dialer-name} [overload] | static + local-ip global-ip}
  + ip nat inside source static + 10.10.10.10 199.99.9.33 + To enable NAT of the inside source + address, use the + ip nat inside source + global configuration command. To + remove the static translation or remove the dynamic association to a + pool, use the + no + form of this command. + + ip nat inside source {list {access-list-number |name} {pool + name | + interface dialer-name} [overload] | static + local-ip global-ip}
+ 1.1.5 + show ip nat statistics + To display NAT statistics, use the + + show ip nat statistics + EXEC command. + show ip nat statistics
  + show ip nat translations + To display active NAT translations, use + the + show ip nat translations + EXEC command. + + show ip nat translations [verbose]
  + clear ip nat translation * + To clear dynamic NAT translations from + the translation table, use the clear + + + ip nat + translation EXEC command. + clear ip nat translation {* | + [inside global-ip local-ip] [outside local-ip global-ip]}
  + + clear ip nat translation inside global-ip local-ip [outside local-ip + global-ip] + To clear dynamic NAT translations from + the translation table, use the + + clear ip nat translation + EXEC command. + clear ip nat translation {* | + [inside global-ip local-ip] [outside local-ip global-ip]}
  + + clear ip nat translation protocol inside global-ip global-port local-ip + local-port [outside local-ip local-port global-ip global-port] + To clear extended dynamic NAT translations from + the translation table, use the + clear ip nat translation EXEC command. + clear ip nat translation + protocol inside global-ip global-port local-ip + local-port [outside local-ip global-ip]
+ 1.1.6 + debug ip nat + Use this command to verify the operation of the NAT feature by + displaying information about every packet that is translated by the + router. + + debug ip nat
  + debug ip nat detailed + This command generates a description of each packet considered for + translation. This command also outputs information about certain + errors or exception conditions, such as the failure to allocate a + global address. + + debug ip nat detailed
+ 1.2.5 + ip dhcp pool + To activate the IOS DHCP server and configure pool-specific settings, + use the + ip dhcp pool + command. To remove the address pool, use the + no + form of this command. + + ip dhcp pool + pool-name +
  + ip dhcp excluded-address + The DHCP Server assumes that all IP addresses in a DHCP address pool + subnet are available for assigning to DHCP clients. You must specify + the IP address that the DHCP Server should not assign to clients. + dhcp excluded-address + low-address + [high-address]
  + default-router + This command specifies the IP address of the default router for a DHCP + client. One IP address is required but up to eight IP addresses may be + specified. To disable this feature, use the no form of this command. + default-router + address [address2 ... + address8]
  + dns-server + This command specifies the IP address of a DNS server that is + available to a DHCP client. To disable this feature, use the no form + of this command. + dns-server + address [address2 ... + address8]
  + netbios-name-server + This command specifies the IP address of a netbios name server that is + available to a DHCP client. One IP address is required. However, up to + eight IP addresses can be specified in one command line. To remove + the NetBIOS name server list, use the + no + form of this command. + netbios-name-server address [address2 ... + address8]
  + no service dhcp + Enables the CiscoIOS DHCP server and relay features on the router. + Use the + no + form of this command to disable the Cisco IOS DHCP server + and relay features. + no service dhcp
  + service dhcp + Enables the CiscoIOS DHCP server and relay features on the router. + Use the + no + form of this command to disable the Cisco IOS DHCP server + and relay features. + service dhcp
  + domain-name + This command specifies the domain name for the client. To remove the + domain name, use the + no + form of this command. + + domain-name domain
+ 1.2.6 + show ip dhcp binding + This command is used to display DHCP server information from EXEC + mode. This displays a list of all bindings created by the DHCP + service. + show ip dhcp {binding + [address] | conflict [address] | database [url] | + server statistics}
  + show ip dhcp server statistics + This command is used to display DHCP server information from EXEC + mode. This will display count information regarding the number of DHCP + messages that have been sent and received. + show ip dhcp {binding + [address] | conflict [address] | database [url] | + server statistics}
+ 1.2.8 + ip helper-address + To have the Cisco IOS software forward User Datagram Protocol (UDP) + broadcasts, including BOOTP, received on an interface, use the + + ip + helper-address interface + configuration command. To disable the + forwarding of broadcast packets to specific addresses, use the no form + of this command. + + ip helper-address address
+ +
+ +
+ +
+ +
+ +
+ + + + + + + +
+ Close Window
+ + + + + + + + + +
+ All contents + copyright © 2003 Cisco Systems, Inc. All rights reserved.
+ +  \ No newline at end of file -- cgit v1.2.3